FRENES

Alpina D3 PCD

2013–2019
VERIFIED
⌀72.6
PCD5x120 or 5x112
Centre bore72.6 or 66.6 mm
Offset (ET)ET28 to ET36
Fixing typeM12x1.50
Tightening torque120 Nm
Original tyres245/35R19, 255/35R19
⚠ This model comes with 5x120 or 5x112 depending on the year or version. Check on an original wheel or with a professional before buying anything.
Hub centric rings 72.6 mm → Wheel spacers 5x120(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Alpina D3

A Alpina D3 (2013–2019) uses a 5x120 or 5x112 PCD and a centre bore of 72.6 or 66.6 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

  • PCD: 5x120 or 5x112 required. See all vehicles with 5x120.
  • Centre bore: the wheel must have a centre bore of 72.6 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 72.6 mm.
  • Offset: the original is ET28 to ET36. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
  • Fixings: thread M12x1.50, tightened to 120 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.
  • Tyres: original fitment is 245/35R19, 255/35R19. For another size, check the diameter difference with the equivalence calculator (under 3 % recommended).

All recorded versions (2)

The original specs vary with the year, trim or wheel size. Identify your version from the tyre size marked on the sidewall.

VersionPCDCentre boreWheelOffsetTyre
Version 1 5x120 72.6 mm — ET36 245/35R19
Version 2 5x112 66.6 mm — ET28 255/35R19

Vehicles with the same PCD and centre bore

Same 5x120 PCD and same 72.6 mm centre bore: wheels from these vehicles bolt on and centre on a Alpina D3 without rings. Offset, width, diameter and caliper clearance still need checking.

Alpina B4 axe arrière 2014–2019 Alpina B4 axe avant 2014–2019 Alpina B3 2013–2019 Alpina D5 2011–2017 Alpina B10 1988–1996 Land Rover Range Rover V from 2022 Land Rover Discovery V from 2017 BMW M2 from 2016 Rolls-Royce Dawn 2015–2022 Rolls-Royce Wraith from 2013 Lamborghini Aventador from 2011 BMW X6 M E71 axe arrière 2009–2014 Rolls-Royce Ghost 2009–2014 BMW X6 E71 axe arrière 2008–2014 Fisker Latigo CS 2005–2007 Rolls-Royce Phantom VII 2003–2016

Will wheels from another vehicle fit your D3?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Frequently asked questions

What is the PCD of a Alpina D3?

A Alpina D3 (2013–2019) can have a 5x120 or 5x112 PCD depending on the version: check on an original wheel.

Does a Alpina D3 need a hub centric ring?

The centre bore (hub diameter) of a Alpina D3 is 72.6 or 66.6 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Alpina D3?

The recorded original offset is ET28 to ET36 depending on the version and wheel size. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Alpina D3?

The specified tightening torque is 120 Nm for M12x1.50 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Which vehicles have the same PCD as a Alpina D3?

With the same PCD (5x120) and the same centre bore (72.6 mm), these include: Alpina B4 axe arrière, Alpina B4 axe avant, Alpina B3, Alpina D5. Offset, width and rim diameter still need checking for each vehicle.

Does a value look wrong, or is a version missing? Let us know, we check every report.