FRENES

Fiat Panda I PCD

1980–2003
VERIFIED
⌀58.1
PCD4x98
Centre bore58.1 mm
Offset (ET)ET35 to ET41
Fixing typeM12x1.25
Tightening torque86 Nm
Original tyres155/80R13, 175/65R14
Hub centric rings 58.1 mm → Wheel spacers 4x98(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Fiat Panda I

A Fiat Panda I (1980–2003) uses a 4x98 PCD and a centre bore of 58.1 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

  • PCD: 4x98 required. See all vehicles with 4x98.
  • Centre bore: the wheel must have a centre bore of 58.1 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 58.1 mm.
  • Offset: the original is ET35 to ET41. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
  • Fixings: thread M12x1.25, tightened to 86 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.
  • Tyres: original fitment is 155/80R13, 175/65R14. For another size, check the diameter difference with the equivalence calculator (under 3 % recommended).

All recorded versions (3)

The original specs vary with the year, trim or wheel size. Identify your version from the tyre size marked on the sidewall.

VersionPCDCentre boreWheelOffsetTyre
Version 1 4x98 58.1 mm — ET41 —
Version 2 4x98 58.1 mm — ET35 155/80R13
Version 3 4x98 58.1 mm — ET35 175/65R14

Vehicles with the same PCD and centre bore

Same 4x98 PCD and same 58.1 mm centre bore: wheels from these vehicles bolt on and centre on a Fiat Panda I without rings. Offset, width, diameter and caliper clearance still need checking.

Fiat 500e 2013–2019 Fiat Panda III from 2012 Fiat Qubo from 2010 Fiat 500 (312) from 2007 Fiat Linea 2007–2016 Fiat Idea 2003–2016 Fiat Panda 4x4 2003–2012 Fiat Albea 2002–2012 Fiat Doblo 2001–2005 Fiat Stilo 2001–2007 Fiat Multipla 1999–2010 Fiat Palio 1998–2006 Fiat Seicento 1998–2010 Fiat Marea 1996–2001 Fiat Petra 1996–2012 Fiat Siena 1996–2012

Will wheels from another vehicle fit your Panda I?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Frequently asked questions

What is the PCD of a Fiat Panda I?

A Fiat Panda I (1980–2003) has a PCD of 4x98: 4 studs or bolts spaced around a circle 98 mm in diameter.

Does a Fiat Panda I need a hub centric ring?

The centre bore (hub diameter) of a Fiat Panda I is 58.1 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Fiat Panda I?

The recorded original offset is ET35 to ET41 depending on the version and wheel size. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Fiat Panda I?

The specified tightening torque is 86 Nm for M12x1.25 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Which vehicles have the same PCD as a Fiat Panda I?

With the same PCD (4x98) and the same centre bore (58.1 mm), these include: Fiat 500e, Fiat Panda III, Fiat Qubo, Fiat 500 (312). Offset, width and rim diameter still need checking for each vehicle.

Does a value look wrong, or is a version missing? Let us know, we check every report.