Ford Crown PCD

1960–1972

VERIFIED

Centre bore70.3 mm

Fixing typeEcrous - 12x1.50

Tightening torque135 Nm

Hub centric rings 70.3 mm → Wheel spacers 5x114.3(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Ford Crown

A Ford Crown (1960–1972) uses a 5x114.3 PCD and a centre bore of 70.3 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

PCD: 5x114.3 required. See all vehicles with 5x114.3.
Centre bore: the wheel must have a centre bore of 70.3 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 70.3 mm.
Fixings: thread Ecrous - 12x1.50, tightened to 135 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.

Vehicles with the same PCD and centre bore

Same 5x114.3 PCD and same 70.3 mm centre bore: wheels from these vehicles bolt on and centre on a Ford Crown without rings. Offset, width, diameter and caliper clearance still need checking.

Ford Flex 2009–2019 Ford Mustang Shelby GT500 2006–2014 Ford Mustang 1979–1993 Ford Torino 1968–1976 Ford Ranchero 1965–1984 Ford Fairline 1955–1970

Will wheels from another vehicle fit your Crown?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Make

Model

Same PCD, different centre bore

These vehicles also use 5x114.3 but with a different centre bore: their wheels need a hub centric ring if their centre bore is larger than 70.3 mm, and will not fit if it is smaller.

Ford Edge ⌀70.6 Ford 500 ⌀63.4 Ford GT axe arrière ⌀70.5 Ford GT axe avant ⌀70.5 Ford Freestar ⌀63.4 Ford Freestyle ⌀63.4 Ford Escape ⌀67.1 Ford Maverick ⌀67.1

Frequently asked questions

What is the PCD of a Ford Crown?

A Ford Crown (1960–1972) has a PCD of 5x114.3: 5 studs or bolts spaced around a circle 114.3 mm in diameter.

Does a Ford Crown need a hub centric ring?

The centre bore (hub diameter) of a Ford Crown is 70.3 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What tightening torque for the wheels of a Ford Crown?

The specified tightening torque is 135 Nm for Ecrous - 12x1.50 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Which vehicles have the same PCD as a Ford Crown?

With the same PCD (5x114.3) and the same centre bore (70.3 mm), these include: Ford Flex, Ford Mustang Shelby GT500, Ford Mustang, Ford Torino. Offset, width and rim diameter still need checking for each vehicle.

Other Ford models

Capri 5x112 Explorer EV 5x112 Transit Courier 5x108 Tourneo Courier 5x108 E-Transit 5x160 Mustang Mach-E 5x108 Puma (J2K) 5x108 Kuga III 5x108 Focus IV 5x108 Fiesta MK8 4x108 Tourneo 5x160 EcoSport 4x108 All Ford →

Does a value look wrong, or is a version missing? Let us know, we check every report.