FRENES

Ford Crown Victoria PCD

1992–1997
VERIFIED
⌀70.5
PCD5x114.3
Centre bore70.5 mm
Offset (ET)ET11.4 to ET54
Fixing typeEcrous - 1/2 - 20 UN
Tightening torque130 Nm
Original tyres215/70R15, 225/60R16
Hub centric rings 70.5 mm → Wheel spacers 5x114.3(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Ford Crown Victoria

A Ford Crown Victoria (1992–1997) uses a 5x114.3 PCD and a centre bore of 70.5 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

  • PCD: 5x114.3 required. See all vehicles with 5x114.3.
  • Centre bore: the wheel must have a centre bore of 70.5 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 70.5 mm.
  • Offset: the original is ET11.4 to ET54. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
  • Fixings: thread Ecrous - 1/2 - 20 UN, tightened to 130 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.
  • Tyres: original fitment is 215/70R15, 225/60R16. For another size, check the diameter difference with the equivalence calculator (under 3 % recommended).

All recorded versions (2)

The original specs vary with the year, trim or wheel size. Identify your version from the tyre size marked on the sidewall.

VersionPCDCentre boreWheelOffsetTyre
Version 1 5x114.3 70.5 mm — ET11.4 215/70R15
Version 2 5x114.3 70.5 mm — ET54 225/60R16

Vehicles with the same PCD and centre bore

Same 5x114.3 PCD and same 70.5 mm centre bore: wheels from these vehicles bolt on and centre on a Ford Crown Victoria without rings. Offset, width, diameter and caliper clearance still need checking.

Ford GT axe arrière 2005–2006 Ford GT axe avant 2005–2006

Will wheels from another vehicle fit your Crown Victoria?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Frequently asked questions

What is the PCD of a Ford Crown Victoria?

A Ford Crown Victoria (1992–1997) has a PCD of 5x114.3: 5 studs or bolts spaced around a circle 114.3 mm in diameter.

Does a Ford Crown Victoria need a hub centric ring?

The centre bore (hub diameter) of a Ford Crown Victoria is 70.5 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Ford Crown Victoria?

The recorded original offset is ET11.4 to ET54 depending on the version and wheel size. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Ford Crown Victoria?

The specified tightening torque is 130 Nm for Ecrous - 1/2 - 20 UN fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Which vehicles have the same PCD as a Ford Crown Victoria?

With the same PCD (5x114.3) and the same centre bore (70.5 mm), these include: Ford GT axe arrière, Ford GT axe avant. Offset, width and rim diameter still need checking for each vehicle.

Does a value look wrong, or is a version missing? Let us know, we check every report.