Land Rover Range Rover II PCD

1995–2002

VERIFIED

Centre bore70.1 mm

Offset (ET)ET57

Fixing typeEcrous - 14x1.50

Tightening torque130 Nm

Hub centric rings 70.1 mm → Wheel spacers 5x120(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Land Rover Range Rover II

A Land Rover Range Rover II (1995–2002) uses a 5x120 PCD and a centre bore of 70.1 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

PCD: 5x120 required. See all vehicles with 5x120.
Centre bore: the wheel must have a centre bore of 70.1 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 70.1 mm.
Offset: the original is ET57. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
Fixings: thread Ecrous - 14x1.50, tightened to 130 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.

Vehicles with the same PCD and centre bore

Same 5x120 PCD and same 70.1 mm centre bore: wheels from these vehicles bolt on and centre on a Land Rover Range Rover II without rings. Offset, width, diameter and caliper clearance still need checking.

Land Rover Discovery II 1998–2005 Acura NSX axe arrière from 2016 Acura NSX axe avant from 2016 Honda NSX axe arrière from 2016 Honda NSX axe avant from 2016

Will wheels from another vehicle fit your Range Rover II?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Make

Model

Same PCD, different centre bore

These vehicles also use 5x120 but with a different centre bore: their wheels need a hub centric ring if their centre bore is larger than 70.1 mm, and will not fit if it is smaller.

Land Rover Range Rover V ⌀72.6 Land Rover Discovery V ⌀72.6 Land Rover Range Rover IV ⌀72.5 Land Rover Discovery IV ⌀72.5 Land Rover Discovery III ⌀72.5 Land Rover Range Rover III ⌀72.5 Land Rover Defender ⌀72.6 Lexus TX ⌀60.1

Frequently asked questions

What is the PCD of a Land Rover Range Rover II?

A Land Rover Range Rover II (1995–2002) has a PCD of 5x120: 5 studs or bolts spaced around a circle 120 mm in diameter.

Does a Land Rover Range Rover II need a hub centric ring?

The centre bore (hub diameter) of a Land Rover Range Rover II is 70.1 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Land Rover Range Rover II?

The recorded original offset is ET57. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Land Rover Range Rover II?

The specified tightening torque is 130 Nm for Ecrous - 14x1.50 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Which vehicles have the same PCD as a Land Rover Range Rover II?

With the same PCD (5x120) and the same centre bore (70.1 mm), these include: Land Rover Discovery II, Acura NSX axe arrière, Acura NSX axe avant, Honda NSX axe arrière. Offset, width and rim diameter still need checking for each vehicle.

Other Land Rover models

Range Rover V 5x120 Discovery V 5x120 Range Rover Velar 5x108 Range Rover IV 5x120 Evoque 5x108 Discovery IV 5x120 Freelander II 5x108 Discovery III 5x120 Range Rover III 5x120 Discovery II 5x120 Freelander 5x114.3 Discovery I 5x165.1 All Land Rover →

Does a value look wrong, or is a version missing? Let us know, we check every report.