FRENES

Seat Alhambra II PCD

2010–2020
VERIFIED
⌀57.1
PCD5x112
Centre bore57.1 mm
Offset (ET)ET33 to ET39
Fixing typeM14x1.5
Tightening torque140 Nm
Original tyres205/60R16, 215/60R16, 225/50R17, 225/45R18
Alhambra 7N, jumelle du VW Sharan II.
Wheel spacers for this vehicle, from €29.95(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Seat Alhambra II

A Seat Alhambra II (2010–2020) uses a 5x112 PCD and a centre bore of 57.1 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

  • PCD: 5x112 required. See all vehicles with 5x112.
  • Centre bore: the wheel must have a centre bore of 57.1 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 57.1 mm.
  • Offset: the original is ET33 to ET39. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
  • Fixings: thread M14x1.5, tightened to 140 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.
  • Tyres: original fitment is 205/60R16, 215/60R16, 225/50R17, 225/45R18. For another size, check the diameter difference with the equivalence calculator (under 3 % recommended).

Generations of the Seat Alhambra

Previous generation: Seat Alhambra (1996–2001) — same 5x112 bolt pattern and same centre bore: original wheels swap between the two generations; check offset and diameter.

Alhambra 1996–2001 · 5x112 Alhambra II 2010–2020

All recorded versions (4)

The original specs vary with the year, trim or wheel size. Identify your version from the tyre size marked on the sidewall.

VersionPCDCentre boreWheelOffsetTyre
Version 1 5x112 57.1 mm 6.5Jx16 ET33 205/60R16
Version 2 5x112 57.1 mm 6.5Jx16 ET33 215/60R16
Version 3 5x112 57.1 mm 7Jx17 ET39 225/50R17
Version 4 5x112 57.1 mm 7.5Jx18 ET35 225/45R18

Vehicles with the same PCD and centre bore

Same 5x112 PCD and same 57.1 mm centre bore: wheels from these vehicles bolt on and centre on a Seat Alhambra II without rings. Offset, width, diameter and caliper clearance still need checking.

Seat Leon Cupra Sportstourer from 2020 Seat Leon IV from 2020 Seat Tarraco from 2018 Seat Ateca from 2016 Seat Leon Cupra ST 2015–2020 Seat Leon Cupra 2014–2020 Seat Leon III 2012–2020 Seat Exeo 2009–2013 Seat Altea Freetrack 2007–2015 Seat Altea XL 2006–2015 Seat Leon II 2005–2012 Seat Altea 2004–2015 Seat Leon I 1999–2005 Seat Alhambra 1996–2001 Seat Toledo 1991–1998 Cupra Terramar from 2024

Will wheels from another vehicle fit your Alhambra II?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Frequently asked questions

What is the PCD of a Seat Alhambra II?

A Seat Alhambra II (2010–2020) has a PCD of 5x112: 5 studs or bolts spaced around a circle 112 mm in diameter.

Does a Seat Alhambra II need a hub centric ring?

The centre bore (hub diameter) of a Seat Alhambra II is 57.1 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Seat Alhambra II?

The recorded original offset is ET33 to ET39 depending on the version and wheel size. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Seat Alhambra II?

The specified tightening torque is 140 Nm for M14x1.5 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Which vehicles have the same PCD as a Seat Alhambra II?

With the same PCD (5x112) and the same centre bore (57.1 mm), these include: Seat Leon Cupra Sportstourer, Seat Leon IV, Seat Tarraco, Seat Ateca. Offset, width and rim diameter still need checking for each vehicle.

Does a value look wrong, or is a version missing? Let us know, we check every report.