Daihatsu Hijet PCD

1987–1993

VERIFIED

Centre bore66.1 or 54.1 mm

Offset (ET)ET40

Fixing typeEcrous - 12x1.50

Tightening torque100 Nm

Original tyres155/75R12, 155/80R12, 155/65R13

⚠ This model comes with 4x110 or 4x100 depending on the year or version. Check on an original wheel or with a professional before buying anything.

Hub centric rings 66.1 mm → Wheel spacers 4x110(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Daihatsu Hijet

A Daihatsu Hijet (1987–1993) uses a 4x110 or 4x100 PCD and a centre bore of 66.1 or 54.1 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

PCD: 4x110 or 4x100 required. See all vehicles with 4x110.
Centre bore: the wheel must have a centre bore of 66.1 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 66.1 mm.
Offset: the original is ET40. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
Fixings: thread Ecrous - 12x1.50, tightened to 100 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.
Tyres: original fitment is 155/75R12, 155/80R12, 155/65R13. For another size, check the diameter difference with the equivalence calculator (under 3 % recommended).

All recorded versions (3)

The original specs vary with the year, trim or wheel size. Identify your version from the tyre size marked on the sidewall.

Version	PCD	Centre bore	Wheel	Offset	Tyre
Version 1	4x110	66.1 mm	—	ET40	155/75R12
Version 2	4x110	66.1 mm	—	ET40	155/80R12
Version 3	4x100	54.1 mm	—	ET40	155/65R13

Will wheels from another vehicle fit your Hijet?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Make

Model

Which original wheels fit a Daihatsu Hijet?

Wheel-by-wheel details (offset, tyres) for vehicles with the same hub:

Wheels from Daihatsu Trevis from 2006 Wheels from Daihatsu YRV 2000–2006 Wheels from Daihatsu Cuore 1990–1998 Wheels from Daihatsu Charade 1987–1993

Same PCD, different centre bore

These vehicles also use 4x110 but with a different centre bore: their wheels need a hub centric ring if their centre bore is larger than 66.1 mm, and will not fit if it is smaller.

Daihatsu Move L601 ⌀56.1 Daihatsu Midget II ⌀56.1 Daihatsu Cuore ⌀56.1 Renault 5 GT Turbo ⌀60.1 Mazda 626 ⌀59.6 Mazda RX-7 ⌀59.6

Frequently asked questions

What is the PCD of a Daihatsu Hijet?

A Daihatsu Hijet (1987–1993) can have a 4x110 or 4x100 PCD depending on the version: check on an original wheel.

Does a Daihatsu Hijet need a hub centric ring?

The centre bore (hub diameter) of a Daihatsu Hijet is 66.1 or 54.1 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Daihatsu Hijet?

The recorded original offset is ET40 depending on the version and wheel size. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Daihatsu Hijet?

The specified tightening torque is 100 Nm for Ecrous - 12x1.50 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Other Daihatsu models

Trevis 4x100 Materia 4x100 Mira Gino 4x100 Copen 4x100 YRV 4x100 Move L901 4x100 Sirion 4x100 Gran Move 4x100 Move L601 4x110 Terios 5x114.3 Midget II 4x110 Cuore 4x100 All Daihatsu →

Does a value look wrong, or is a version missing? Let us know, we check every report.