FRENES

Fisker Latigo CS PCD

2005–2007
VERIFIED
⌀72.6
PCD5x120
Centre bore72.6 mm
Offset (ET)ET10
Fixing typeM12x1.50
Tightening torque140 Nm
Original tyres255/35R20
Hub centric rings 72.6 mm → Wheel spacers 5x120(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Fisker Latigo CS

A Fisker Latigo CS (2005–2007) uses a 5x120 PCD and a centre bore of 72.6 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

  • PCD: 5x120 required. See all vehicles with 5x120.
  • Centre bore: the wheel must have a centre bore of 72.6 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 72.6 mm.
  • Offset: the original is ET10. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
  • Fixings: thread M12x1.50, tightened to 140 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.
  • Tyres: original fitment is 255/35R20. For another size, check the diameter difference with the equivalence calculator (under 3 % recommended).

Vehicles with the same PCD and centre bore

Same 5x120 PCD and same 72.6 mm centre bore: wheels from these vehicles bolt on and centre on a Fisker Latigo CS without rings. Offset, width, diameter and caliper clearance still need checking.

Land Rover Range Rover V from 2022 Land Rover Discovery V from 2017 BMW M2 from 2016 Rolls-Royce Dawn 2015–2022 Alpina B4 axe arrière 2014–2019 Alpina B4 axe avant 2014–2019 Alpina B3 2013–2019 Alpina D3 2013–2019 Rolls-Royce Wraith from 2013 Alpina D5 2011–2017 Lamborghini Aventador from 2011 BMW X6 M E71 axe arrière 2009–2014 Rolls-Royce Ghost 2009–2014 BMW X6 E71 axe arrière 2008–2014 Rolls-Royce Phantom VII 2003–2016 Alpina B10 1988–1996

Will wheels from another vehicle fit your Latigo CS?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Frequently asked questions

What is the PCD of a Fisker Latigo CS?

A Fisker Latigo CS (2005–2007) has a PCD of 5x120: 5 studs or bolts spaced around a circle 120 mm in diameter.

Does a Fisker Latigo CS need a hub centric ring?

The centre bore (hub diameter) of a Fisker Latigo CS is 72.6 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Fisker Latigo CS?

The recorded original offset is ET10. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Fisker Latigo CS?

The specified tightening torque is 140 Nm for M12x1.50 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Which vehicles have the same PCD as a Fisker Latigo CS?

With the same PCD (5x120) and the same centre bore (72.6 mm), these include: Land Rover Range Rover V, Land Rover Discovery V, BMW M2, Rolls-Royce Dawn. Offset, width and rim diameter still need checking for each vehicle.

Does a value look wrong, or is a version missing? Let us know, we check every report.