Mitsubishi L200 PCD

1986–1996

VERIFIED

Centre bore108.1 mm

Offset (ET)ET15

Fixing typeEcrous - 12x1.50

Tightening torque110 Nm

Hub centric rings 108.1 mm → Wheel spacers 6x139.7(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Mitsubishi L200

A Mitsubishi L200 (1986–1996) uses a 6x139.7 PCD and a centre bore of 108.1 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

PCD: 6x139.7 required. See all vehicles with 6x139.7.
Centre bore: the wheel must have a centre bore of 108.1 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 108.1 mm.
Offset: the original is ET15. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
Fixings: thread Ecrous - 12x1.50, tightened to 110 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.

Will wheels from another vehicle fit your L200?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Make

Model

Same PCD, different centre bore

These vehicles also use 6x139.7 but with a different centre bore: their wheels need a hub centric ring if their centre bore is larger than 108.1 mm, and will not fit if it is smaller.

Mitsubishi Pajero Shogun ⌀67.1 Mitsubishi Pajero Sport ⌀107.4 Mitsubishi Pajero Wagon ⌀67.1 Mitsubishi L200 2WD ⌀107.4 Mitsubishi L200 4WD ⌀67.1 Mitsubishi L400 4WD ⌀107.4 Mitsubishi L300 4WD ⌀107.4 Mitsubishi Pajero ⌀107.4

Frequently asked questions

What is the PCD of a Mitsubishi L200?

A Mitsubishi L200 (1986–1996) has a PCD of 6x139.7: 6 studs or bolts spaced around a circle 139.7 mm in diameter.

Does a Mitsubishi L200 need a hub centric ring?

The centre bore (hub diameter) of a Mitsubishi L200 is 108.1 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Mitsubishi L200?

The recorded original offset is ET15. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Mitsubishi L200?

The specified tightening torque is 110 Nm for Ecrous - 12x1.50 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Other Mitsubishi models

Eclipse Cross 5x114.3 ASX 5x114.3 i-MiEV 4x100 Lancer EVO X 5x114.3 Lancer EVO IX 5x114.3 Grandis 5x114.3 Lancer 1.3i, 1.6i 4x114.3 Outlander 5x114.3 Lancer EVO VIII 5x114.3 Lancer 2.0i 5x114.3 Airtrek 5x114.3 Lancer EVO VII 5x114.3 All Mitsubishi →

Does a value look wrong, or is a version missing? Let us know, we check every report.