A Ford Mondeo IV (2007–2014) uses a 5x108 PCD and a centre bore of 63.4 mm.
Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.
Centre bore: the wheel must have a centre bore of 63.4 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 63.4 mm.
Offset: the original is ET50 to ET55. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
Fixings: thread M12x1.5, tightened to 135 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.
Tyres: original fitment is 205/55R16, 215/55R16, 215/50R17, 235/45R17. For another size, check the diameter difference with the equivalence calculator (under 3 % recommended).
Generations of the Ford Mondeo
Previous generation: Ford Mondeo ST200 (1995–2000) — the bolt pattern changes (5x108 instead of 4x108): the wheels are not interchangeable. Next generation: Ford Mondeo V (2014–2022) — same 5x108 bolt pattern and same centre bore: original wheels swap between the two generations; check offset and diameter.
The original specs vary with the year, trim or wheel size. Identify your version from the tyre size marked on the sidewall.
Version
PCD
Centre bore
Wheel
Offset
Tyre
Version 1
5x108
63.4 mm
6.5Jx16
ET50
205/55R16
Version 2
5x108
63.4 mm
6.5Jx16
ET50
215/55R16
Version 3
5x108
63.4 mm
7Jx17
ET50
215/50R17
Version 4
5x108
63.4 mm
7.5Jx17
ET55
235/45R17
Version 5
5x108
63.4 mm
8Jx18
ET55
235/40R18
Version 6
5x108
63.4 mm
8Jx18
ET55
235/45R18
Version 7
5x108
63.4 mm
8Jx19
ET55
235/40R19
Vehicles with the same PCD and centre bore
Same 5x108 PCD and same 63.4 mm centre bore: wheels from these vehicles bolt on and centre on a Ford Mondeo IV without rings. Offset, width, diameter and caliper clearance still need checking.
These vehicles also use 5x108 but with a different centre bore: their wheels need a hub centric ring if their centre bore is larger than 63.4 mm, and will not fit if it is smaller.
A Ford Mondeo IV (2007–2014) has a PCD of 5x108: 5 studs or bolts spaced around a circle 108 mm in diameter.
Does a Ford Mondeo IV need a hub centric ring?
The centre bore (hub diameter) of a Ford Mondeo IV is 63.4 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.
What offset (ET) for a Ford Mondeo IV?
The recorded original offset is ET50 to ET55 depending on the version and wheel size. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.
What tightening torque for the wheels of a Ford Mondeo IV?
The specified tightening torque is 135 Nm for M12x1.5 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.
Which vehicles have the same PCD as a Ford Mondeo IV?
With the same PCD (5x108) and the same centre bore (63.4 mm), these include: Ford Tourneo Courier, Ford Transit Courier, Ford Mustang Mach-E, Ford Kuga III. Offset, width and rim diameter still need checking for each vehicle.
Does a value look wrong, or is a version missing? Let us know, we check every report.
Cookies : we use audience measurement cookies (Google Analytics) and, if you accept, advertising cookies. You can change your mind at any time via “Manage cookies” at the bottom of the page. Learn more