Isuzu Campo 4WD PCD

1988–2003

VERIFIED

Centre bore110 mm

Offset (ET)ET38

Fixing typeEcrous - 12x1.50

Tightening torque82 Nm

Hub centric rings 110 mm → Wheel spacers 6x139.7(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Isuzu Campo 4WD

A Isuzu Campo 4WD (1988–2003) uses a 6x139.7 PCD and a centre bore of 110 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

PCD: 6x139.7 required. See all vehicles with 6x139.7.
Centre bore: the wheel must have a centre bore of 110 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 110 mm.
Offset: the original is ET38. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
Fixings: thread Ecrous - 12x1.50, tightened to 82 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.

Vehicles with the same PCD and centre bore

Same 6x139.7 PCD and same 110 mm centre bore: wheels from these vehicles bolt on and centre on a Isuzu Campo 4WD without rings. Offset, width, diameter and caliper clearance still need checking.

Isuzu Campo 2WD 1988–2003 Isuzu Trooper 1981–1991 Kia Bongo from 2000 Kia Pregio from 2000 Nissan Patrol GR 1997–2010 Ssang Yong Korando 1997–2001 Ssang Yong Musso 1993–2005 Opel Campo 2WD 1988–2003 Opel Campo 4WD 1988–2003

Will wheels from another vehicle fit your Campo 4WD?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Make

Model

Same PCD, different centre bore

These vehicles also use 6x139.7 but with a different centre bore: their wheels need a hub centric ring if their centre bore is larger than 110 mm, and will not fit if it is smaller.

Isuzu D-Max ⌀100.1 Infiniti QX80 ⌀77.8 Hyundai Staria ⌀92.5 RAM RAM 1500 ⌀77.8 GMC Sierra 1500 ⌀78.1 Holden Colorado ⌀99.5 Lexus GX460 ⌀106 Hyundai H-1 H300 ⌀92.3

Frequently asked questions

What is the PCD of a Isuzu Campo 4WD?

A Isuzu Campo 4WD (1988–2003) has a PCD of 6x139.7: 6 studs or bolts spaced around a circle 139.7 mm in diameter.

Does a Isuzu Campo 4WD need a hub centric ring?

The centre bore (hub diameter) of a Isuzu Campo 4WD is 110 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Isuzu Campo 4WD?

The recorded original offset is ET38. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Isuzu Campo 4WD?

The specified tightening torque is 82 Nm for Ecrous - 12x1.50 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Which vehicles have the same PCD as a Isuzu Campo 4WD?

With the same PCD (6x139.7) and the same centre bore (110 mm), these include: Isuzu Campo 2WD, Isuzu Trooper, Kia Bongo, Kia Pregio. Offset, width and rim diameter still need checking for each vehicle.

Other Isuzu models

D-Max 6x139.7 Oasis 5x114.3 Gemini 4x100 Campo 2WD 6x139.7 Piazza 4x100 Trooper 6x139.7 All Isuzu →

Does a value look wrong, or is a version missing? Let us know, we check every report.