Lancia Phedra PCD

2002–2010

VERIFIED

Centre bore58.1 mm

Offset (ET)ET30

Fixing type-

Tightening torque100 Nm

Hub centric rings 58.1 mm → Wheel spacers 5x98(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Lancia Phedra

A Lancia Phedra (2002–2010) uses a 5x98 PCD and a centre bore of 58.1 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

PCD: 5x98 required. See all vehicles with 5x98.
Centre bore: the wheel must have a centre bore of 58.1 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 58.1 mm.
Offset: the original is ET30. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
Fixings: thread -, tightened to 100 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.

Vehicles with the same PCD and centre bore

Same 5x98 PCD and same 58.1 mm centre bore: wheels from these vehicles bolt on and centre on a Lancia Phedra without rings. Offset, width, diameter and caliper clearance still need checking.

Lancia Delta Integrale 5 trou 1994–1999 Lancia Zeta 1994–2002 Fiat e-Doblo from 2022 Alfa Romeo 4C 2013–2020 Fiat 500L Trekking from 2013 RAM Promaster City from 2013 Fiat 500L from 2012 Holden Combo from 2011 Fiat Doblo Maxi 2010–2022 Alfa Romeo GT 2003–2010 Peugeot 807 from 2002 Alfa Romeo 147 2001–2010 Fiat Doblo 2001–2005 Alfa Romeo 156 1997–2006 Citroen Jumpy 1996–2006 Peugeot Expert 1996–2006

Will wheels from another vehicle fit your Phedra?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Make

Model

Same PCD, different centre bore

These vehicles also use 5x98 but with a different centre bore: their wheels need a hub centric ring if their centre bore is larger than 58.1 mm, and will not fit if it is smaller.

Citroen C8 ⌀65.1 Fiat Scudo ⌀65.1 Alfa Romeo 75 5 trou, V6 ⌀58.6

Frequently asked questions

What is the PCD of a Lancia Phedra?

A Lancia Phedra (2002–2010) has a PCD of 5x98: 5 studs or bolts spaced around a circle 98 mm in diameter.

Does a Lancia Phedra need a hub centric ring?

The centre bore (hub diameter) of a Lancia Phedra is 58.1 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Lancia Phedra?

The recorded original offset is ET30. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Lancia Phedra?

The specified tightening torque is 100 Nm for - fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Which vehicles have the same PCD as a Lancia Phedra?

With the same PCD (5x98) and the same centre bore (58.1 mm), these include: Lancia Delta Integrale 5 trou, Lancia Zeta, Fiat e-Doblo, Alfa Romeo 4C. Offset, width and rim diameter still need checking for each vehicle.

Other Lancia models

Flavia 5x114.3 Voyager 5x127 Musa 4x98 Ypsilon 4x98 Thesis 5x108 Lybra 4x98 Y 4x98 Delta Integrale 5 trou 5x98 Kappa 5x108 Zeta 5x98 Delta 4x98 Delta Integrale 4 trou 4x98 All Lancia →

Does a value look wrong, or is a version missing? Let us know, we check every report.