Porsche 924 PCD

1976–1987

VERIFIED

Centre bore57.1 mm

Offset (ET)ET20

Fixing typeM14x1.50

Tightening torque130 Nm

Hub centric rings 57.1 mm → Wheel spacers 4x108(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Porsche 924

A Porsche 924 (1976–1987) uses a 4x108 PCD and a centre bore of 57.1 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

PCD: 4x108 required. See all vehicles with 4x108.
Centre bore: the wheel must have a centre bore of 57.1 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 57.1 mm.
Offset: the original is ET20. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
Fixings: thread M14x1.50, tightened to 130 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.

Vehicles with the same PCD and centre bore

Same 4x108 PCD and same 57.1 mm centre bore: wheels from these vehicles bolt on and centre on a Porsche 924 without rings. Offset, width, diameter and caliper clearance still need checking.

Audi Convertible 1991–2000 Audi 80 1986–1996 Audi 100 1982–1990 Audi Coupe 1980–1988

Will wheels from another vehicle fit your 924?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Make

Model

Same PCD, different centre bore

These vehicles also use 4x108 but with a different centre bore: their wheels need a hub centric ring if their centre bore is larger than 57.1 mm, and will not fit if it is smaller.

Alfa Romeo Junior ⌀65.1 Fiat 600 ⌀65.1 Fiat 600E ⌀65.1 Fiat Topolino ⌀65.1 Jeep Avenger ⌀65.1 Peugeot e-208 ⌀65.1 Opel Rocks-E ⌀65.1 Citroen Ami ⌀65.1

Frequently asked questions

What is the PCD of a Porsche 924?

A Porsche 924 (1976–1987) has a PCD of 4x108: 4 studs or bolts spaced around a circle 108 mm in diameter.

Does a Porsche 924 need a hub centric ring?

The centre bore (hub diameter) of a Porsche 924 is 57.1 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Porsche 924?

The recorded original offset is ET20. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Porsche 924?

The specified tightening torque is 130 Nm for M14x1.50 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Which vehicles have the same PCD as a Porsche 924?

With the same PCD (4x108) and the same centre bore (57.1 mm), these include: Audi Convertible, Audi 80, Audi 100, Audi Coupe. Offset, width and rim diameter still need checking for each vehicle.

Other Porsche models

Taycan 5x130 Boxster 718 5x130 Cayman 718 5x130 Macan 5x112 911 991 Turbo S 5x130 911 997 GTS Écrou central 911 997 GT2 RS Écrou central Panamera 5x130 911 997 GT2 5x130 911 997 Turbo 5x130 911 997 GT3 5x130 911 997 GT3 RS 5x130 All Porsche →

Does a value look wrong, or is a version missing? Let us know, we check every report.