FRENES

Daihatsu Charade PCD

1987–1993
VERIFIED
⌀54.1
PCD4x100
Centre bore54.1 mm
Offset (ET)ET45
Fixing typeEcrous - 12x1.50
Tightening torque99 Nm
Original tyres155/80R13, 155R13
Hub centric rings 54.1 mm → Wheel spacers 4x100(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Daihatsu Charade

A Daihatsu Charade (1987–1993) uses a 4x100 PCD and a centre bore of 54.1 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

  • PCD: 4x100 required. See all vehicles with 4x100.
  • Centre bore: the wheel must have a centre bore of 54.1 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 54.1 mm.
  • Offset: the original is ET45. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
  • Fixings: thread Ecrous - 12x1.50, tightened to 99 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.
  • Tyres: original fitment is 155/80R13, 155R13. For another size, check the diameter difference with the equivalence calculator (under 3 % recommended).

All recorded versions (2)

The original specs vary with the year, trim or wheel size. Identify your version from the tyre size marked on the sidewall.

VersionPCDCentre boreWheelOffsetTyre
Version 1 4x100 54.1 mm — ET45 155/80R13
Version 2 4x100 54.1 mm — ET45 155R13

Vehicles with the same PCD and centre bore

Same 4x100 PCD and same 54.1 mm centre bore: wheels from these vehicles bolt on and centre on a Daihatsu Charade without rings. Offset, width, diameter and caliper clearance still need checking.

Daihatsu Materia from 2006 Daihatsu Mira Gino from 2006 Daihatsu Trevis from 2006 Daihatsu Copen 2002–2012 Daihatsu YRV 2000–2006 Daihatsu Sirion 1998–2004 Daihatsu Cuore 1990–1998 Daihatsu Hijet 1987–1993 Hyundai Inster from 2024 Hyundai Bayon from 2021 Toyota Aygo X 2021–2025 Hyundai i20 III from 2020 Hyundai i10 III from 2019 Kia Picanto III from 2017 Kia Stonic from 2017 Fiat 124 Spider from 2015

Will wheels from another vehicle fit your Charade?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Frequently asked questions

What is the PCD of a Daihatsu Charade?

A Daihatsu Charade (1987–1993) has a PCD of 4x100: 4 studs or bolts spaced around a circle 100 mm in diameter.

Does a Daihatsu Charade need a hub centric ring?

The centre bore (hub diameter) of a Daihatsu Charade is 54.1 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Daihatsu Charade?

The recorded original offset is ET45 depending on the version and wheel size. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Daihatsu Charade?

The specified tightening torque is 99 Nm for Ecrous - 12x1.50 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Which vehicles have the same PCD as a Daihatsu Charade?

With the same PCD (4x100) and the same centre bore (54.1 mm), these include: Daihatsu Materia, Daihatsu Mira Gino, Daihatsu Trevis, Daihatsu Copen. Offset, width and rim diameter still need checking for each vehicle.

Does a value look wrong, or is a version missing? Let us know, we check every report.