Mitsubishi Sapporo PCD

1985–1990

VERIFIED

Centre bore67.1 mm

Offset (ET)ET46

Fixing typeM12x1.50

Tightening torque110 Nm

Hub centric rings 67.1 mm → Wheel spacers 4x114.3(partner link) Change PCD (PCD adapter)(partner link) Sheet for your mechanic

Fitting wheels on a Mitsubishi Sapporo

A Mitsubishi Sapporo (1985–1990) uses a 4x114.3 PCD and a centre bore of 67.1 mm. Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.

PCD: 4x114.3 required. See all vehicles with 4x114.3.
Centre bore: the wheel must have a centre bore of 67.1 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 67.1 mm.
Offset: the original is ET46. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
Fixings: thread M12x1.50, tightened to 110 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.

Vehicles with the same PCD and centre bore

Same 4x114.3 PCD and same 67.1 mm centre bore: wheels from these vehicles bolt on and centre on a Mitsubishi Sapporo without rings. Offset, width, diameter and caliper clearance still need checking.

Mitsubishi Lancer 1.3i, 1.6i 2003–2008 Mitsubishi Carisma 1.6, 1.8GDi,1.9TD 2000–2004 Mitsubishi Space Star 1998–2005 Mitsubishi Carisma 1.8i 1995–2001 Mitsubishi Lancer EVO III 1995–1996 Mitsubishi Lancer EVO II 1994–1995 Mitsubishi Lancer EVO I 1992–1994 Mitsubishi Space Runner 1991–1999 Mitsubishi Space Wagon 1991–1999 Mitsubishi Galant 1989–1992 Mitsubishi Colt 1988–1992 Mitsubishi Lancer 1988–1992 Mitsubishi Cordia 1982–1990 Mitsubishi Starion 1982–1991 Smart Forfour 2004–2007 Kia Cerato 2003–2008

Will wheels from another vehicle fit your Sapporo?

Choose the vehicle the wheels come from: we compare the hub, then each original wheel to the millimetre.

Make

Model

Same PCD, different centre bore

These vehicles also use 4x114.3 but with a different centre bore: their wheels need a hub centric ring if their centre bore is larger than 67.1 mm, and will not fit if it is smaller.

Nissan Evalia ⌀66.1 Nissan NV200 ⌀66.1 Nissan Tiida ⌀66.1 Nissan Versa ⌀66.1 Chery Fora ⌀56.6 Chevrolet Epica ⌀56.6 Chevrolet Evanda ⌀56.6 Chevrolet Lacetti ⌀56.6

Frequently asked questions

What is the PCD of a Mitsubishi Sapporo?

A Mitsubishi Sapporo (1985–1990) has a PCD of 4x114.3: 4 studs or bolts spaced around a circle 114.3 mm in diameter.

Does a Mitsubishi Sapporo need a hub centric ring?

The centre bore (hub diameter) of a Mitsubishi Sapporo is 67.1 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.

What offset (ET) for a Mitsubishi Sapporo?

The recorded original offset is ET46. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.

What tightening torque for the wheels of a Mitsubishi Sapporo?

The specified tightening torque is 110 Nm for M12x1.50 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.

Which vehicles have the same PCD as a Mitsubishi Sapporo?

With the same PCD (4x114.3) and the same centre bore (67.1 mm), these include: Mitsubishi Lancer 1.3i, 1.6i, Mitsubishi Carisma 1.6, 1.8GDi,1.9TD, Mitsubishi Space Star, Mitsubishi Carisma 1.8i. Offset, width and rim diameter still need checking for each vehicle.

Other Mitsubishi models

Eclipse Cross 5x114.3 ASX 5x114.3 i-MiEV 4x100 Lancer EVO X 5x114.3 Lancer EVO IX 5x114.3 Grandis 5x114.3 Lancer 1.3i, 1.6i 4x114.3 Outlander 5x114.3 Lancer EVO VIII 5x114.3 Lancer 2.0i 5x114.3 Airtrek 5x114.3 Lancer EVO VII 5x114.3 All Mitsubishi →

Does a value look wrong, or is a version missing? Let us know, we check every report.