A Toyota RAV4 III (2005–2012) uses a 5x114.3 PCD and a centre bore of 60.1 mm.
Any wheel must match the vehicle's PCD exactly: there is no tolerance, unless you use a PCD adapter.
Centre bore: the wheel must have a centre bore of 60.1 mm or more. If it is larger (as with most aftermarket wheels), add a hub centric ring wheel centre bore → 60.1 mm.
Offset: the original is ET45. Compare your future wheel with the offset calculator (your vehicle is already selected) to see how many millimetres further in or out it will sit.
Fixings: thread M12x1.5, tightened to 103 Nm. The nuts or bolts must have the same seat (conical, spherical or flat) as the wheel.
Tyres: original fitment is 215/70R16, 225/65R17. For another size, check the diameter difference with the equivalence calculator (under 3 % recommended).
Generations of the Toyota RAV4
Previous generation: Toyota RAV4 I (1994–2000) — same 5x114.3 bolt pattern and same centre bore: original wheels swap between the two generations; check offset and diameter. Next generation: Toyota RAV4 IV (2012–2018) — same 5x114.3 bolt pattern and same centre bore: original wheels swap between the two generations; check offset and diameter.
The original specs vary with the year, trim or wheel size. Identify your version from the tyre size marked on the sidewall.
Version
PCD
Centre bore
Wheel
Offset
Tyre
Version 1
5x114.3
60.1 mm
6.5Jx16
ET45
215/70R16
Version 2
5x114.3
60.1 mm
6.5Jx17
ET45
225/65R17
Version 3
5x114.3
60.1 mm
7Jx17
ET45
225/65R17
Vehicles with the same PCD and centre bore
Same 5x114.3 PCD and same 60.1 mm centre bore: wheels from these vehicles bolt on and centre on a Toyota RAV4 III without rings. Offset, width, diameter and caliper clearance still need checking.
These vehicles also use 5x114.3 but with a different centre bore: their wheels need a hub centric ring if their centre bore is larger than 60.1 mm, and will not fit if it is smaller.
A Toyota RAV4 III (2005–2012) has a PCD of 5x114.3: 5 studs or bolts spaced around a circle 114.3 mm in diameter.
Does a Toyota RAV4 III need a hub centric ring?
The centre bore (hub diameter) of a Toyota RAV4 III is 60.1 mm. A wheel with a larger centre bore is fitted with a hub centric ring that brings it down to the hub diameter. A wheel with a smaller centre bore cannot be fitted.
What offset (ET) for a Toyota RAV4 III?
The recorded original offset is ET45 depending on the version and wheel size. A lower ET pushes the wheel outwards, a higher ET pulls it inwards: check wheel well and caliper clearance before making any change.
What tightening torque for the wheels of a Toyota RAV4 III?
The specified tightening torque is 103 Nm for M12x1.5 fixings. Tighten in a criss-cross pattern with a torque wrench and check the tightness again after about fifty kilometres.
Which vehicles have the same PCD as a Toyota RAV4 III?
With the same PCD (5x114.3) and the same centre bore (60.1 mm), these include: Toyota C-HR II, Toyota Prius V, Toyota BZ4X, Toyota Yaris Cross. Offset, width and rim diameter still need checking for each vehicle.
Does a value look wrong, or is a version missing? Let us know, we check every report.
Cookies : we use audience measurement cookies (Google Analytics) and, if you accept, advertising cookies. You can change your mind at any time via “Manage cookies” at the bottom of the page. Learn more